#Rebuilding old craftsman table saw how to

Next should have been to bolt the assembly to the table top followed by bolting the body to the top. Putting it all back together happened in reverse order starting with the blade assembly. I decided to paint the body the same color as the stand and table insert. Honestly, it looked too much like the original saw (too old) and I thatвЂ™s when I noticed the brush strokes from the base coat.ДЄfter waiting for the paint to cure, I sanded the body once again and prepped for a different color. After it dried I immediately disliked the color. My first coat of paint was an antique bronze color. The other part of my mind was excited to finish the project. Part of my mind was thinking I was applying a hammered paint and that the brush marks wouldnвЂ™t be visible. I used a coarse brush when I painted on GEMPLERвЂ™S rust converter. I didnвЂ™t prep the primer surface after painting on the rust converter. It wasnвЂ™t a fancy process and I made several mistakes. I painted the table insert, body, and stand with red Rustoleum paint in rattle cans. Based on my experience with the product it is working as advertised. It purports to be able to chemically convert rust into an inert, black protective barrier. I brushed mine on and found that I needed to wet sand after before painting. The base coat is as smooth as your applicator. It is an all in one rust converter and primer and is available in an aerosol can as well as in one quart/one gallon containers. The product I used is called GEMPLERвЂ™S Rust Converter.

#Rebuilding old craftsman table saw how to

My description is for basic understanding of the process not how to do it. If you want to try it, do your due diligence and research. Wire these together and connect them to the red lead of the battery charger.They aided window operation through ropes and pulleys.) (In my case, I use some left over iron weights from an old window demo. Note: never use anything that is chromed. Place several sacrificial pieces of metal around and not touching the part.Connect the black lead of the charger to this part either directly or wired connection.Suspend the item you want to be cleaned in a solution of water and sodium carbonate.I used a ratio of around ВЅ cup of Arm & Hammer Washing Soda to one gallon of water. Prepare a solution of water and sodium carbonate.In the future IвЂ™m going experiment with higher settings and see if one method is more effective than the other. The process seemed to work well on 2 amps. Some sources suggest using higher amp settings while others insist on using a lower setting such as two amps. This photo is after a day or so of running the battery charger at 2 amps. Red Clamp: to Anode rod вЂ“ Black Clamp: to Cast-iron top IвЂ™m personally still experimenting, learning about the process, and am looking forward to trying it on a few old rusty ax heads I found last summer. ProcedureД®lectrolysis works by sending an electric current from a battery charger to a piece of metal which acts as an anode rod and to the part that needs rust removal through a solution of water and sodium carbonate.ДЄgain, the process sounds complicated, but easy to use effectively. I ended up going with Arm & Hammer washing soda and a charger made by Schumacher. The only two things I didnвЂ™t have in the garage to do it was washing soda (sodium carbonate) and a battery charger. It sounds by far the most complicated method to remove rust, but in practice it was quite simple. On the cast iron top I used electrolysis. I did a lot of cleaning, grinding with a wire-wheel, sanding, and later on buffing. I think this goes without explaining and lacks any real mystery. Here are the methods I experimented with in this project:Д«efore I used any of the fancy and fun procedures, I used good old fashioned elbow grease to prep the surfaces. It was also about the experience of learning how to fix up an old tool. I didnвЂ™t merely want to restore the saw for its use in woodworking. I used a variety of techniques to restore the parts of the saw, not because they were necessarily the best methods, but mostly because they were methods I was curious about and wanted to learn how to do. Being able to reference back to the footage helped me immensely when it came time to reassemble the pieces. IвЂ™m really glad that I filmed this entire project, especially the blade assembly.